# SCARA robot

> Source: https://aiwiki.ai/wiki/scara
> Updated: 2026-11-18
> Fact-checked: 2026-11-18
> Categories: Robot Hardware, Robotics
> License: CC BY 4.0 (https://creativecommons.org/licenses/by/4.0/) - attribute to "AI Wiki (aiwiki.ai)"
> Cite as: AI Wiki. "SCARA robot." aiwiki.ai, 18 Nov 2026. https://aiwiki.ai/wiki/scara
> From AI Wiki (https://aiwiki.ai), the free encyclopedia of artificial intelligence. Reuse freely with attribution.

A **SCARA robot** (Selective Compliance Assembly Robot Arm) is an [industrial robot](https://aiwiki.ai/wiki/industrial_robot) arm with two horizontal links that swing about parallel vertical axes, a tool shaft that moves straight up and down, and a rotation of that tool, giving four [degrees of freedom](https://aiwiki.ai/wiki/degrees_of_freedom) in all.[1] The name describes its main mechanical property: the arm yields easily to sideways forces in the horizontal plane but is stiff in the vertical direction, which helps it push parts into holes during assembly.[1] Hiroshi Makino, then a professor at the University of Yamanashi in Japan, invented the design, and the first prototype was built in 1978 with support from a research consortium of companies.[1][2][13] Manufacturers began selling their own versions in 1981.[1] SCARA arms are used for insertion, pick-and-place, packaging and inspection, and the Robot Hall of Fame credits the design with making possible the high-speed automated assembly behind mass-produced small electronics.[1][2][7] The SCARA was inducted into the Robot Hall of Fame at [Carnegie Mellon University](https://aiwiki.ai/wiki/cmu) in 2006.[1][2]

<figure>
<img src="/images/media-2026-11-18-scara-8b4016bff6a2.jpg" alt="A yellow and black SCARA robot arm with a vertical tool shaft and gripper above trays in an automated work cell" width="1200" height="822" />
<figcaption>A SCARA robot working with a palletizer in an assembly cell. Hirata Robotics GmbH, via <a href="https://commons.wikimedia.org/wiki/File:SCARA_mit_Stocker.jpg">Wikimedia Commons</a>, <a href="https://creativecommons.org/licenses/by-sa/3.0/de/deed.en">CC BY-SA 3.0 de</a>.</figcaption>
</figure>

## Selective compliance

Compliance is the inverse of stiffness. Stiffness, or spring constant, is force divided by displacement; compliance is displacement divided by force, so a highly compliant mechanism moves a long way under a small force.[1] Makino started from a typical assembly problem, inserting a peg into a hole when the two are slightly misaligned and at least one of them has a chamfer or rounded edge. If the peg holder gives way sideways, the chamfer pushes the peg across until it lines up and drops in. If the holder also lets the peg tilt, the peg jams.[1] A good peg holder therefore needs compliance that depends on direction:[1]

| Direction | Compliance wanted |
| --- | --- |
| Horizontal force | Large |
| Vertical force | Small |
| Rotation about the vertical axis | Large |
| Rotation about the horizontal axes | Small |

Makino called this property "selective compliance".[1] He realized it with a structure he compared to a byobu, the traditional Japanese folding screen, which folds easily in the horizontal plane but is stiff vertically. The first two arms of a SCARA rotate about vertical axes and behave like the folding panels of the screen.[1]

The Robot Hall of Fame describes the result as an arm that moves vertically and horizontally like a human arm but has a limited wrist, one that can rotate but not tilt, and notes that this limitation suits pick-and-place, assembly and packaging work.[2]

## History

### Origins at the University of Yamanashi

Makino graduated from the University of Tokyo in 1956 and worked at Matsushita Electric Industrial (now Panasonic) before joining the University of Yamanashi as an associate professor in 1966; he became a professor there in 1976.[1] By his own account, he drew the assembly drawing of the first SCARA prototype himself over the New Year holiday of 1978 and estimated that the machine would cost about 5 million yen to build. A professor's annual research allowance at the time was about 1 million yen, and no company would sponsor a robot proposed by an unknown young professor.[1] Kazuo Yamafuji, then an associate professor at Yamanashi and a member of the project, writes that Makino was stimulated by SIGMA, an assembly robot presented by A. d'Auria of Olivetti at the 7th International Symposium on Industrial Robots in Tokyo in October 1977, and began designing the first prototype two months later.[13]

He instead set up the "SCARA research group", a consortium that companies could join for 1 million yen each, so that five members would pay for the machine. In Makino's account, five companies joined and the group began work in April 1978; it met every two or three months to discuss experiments on the prototypes and the direction of the project, and it ran for three years.[1] Yamafuji's account differs on the membership: he describes a consortium of Yamanashi University and thirteen Japanese companies (Fujitsu, Nitto Seiko, NEC, Pentel, Sankyo, Telmec, CKD, Yamaha Motor, Pioneer, Tenryu Seiki, Ultrasonic Industry, Hitech Seiko and NAIS), formed in March 1978 for a three-year term from April 1978 to March 1981.[13]

### Prototypes and control

Makino dates the first prototype to October 1978; Yamafuji writes that Fujitsu made it, to the university's design, in July 1978.[1][13] It used a DC printed motor and an optical encoder as its main servo elements, and experiments on it confirmed the basic selective-compliance behavior, but its servo motion vibrated.[1] On the suggestion of the servo motor maker [Yaskawa Electric](https://aiwiki.ai/wiki/yaskawa), Prototype II, built in May 1980, used a new DC motor with tacho-generator feedback and showed good motion characteristics.[1] Yamafuji credits Nitto Seiko with fabricating Prototype II.[13]

Makino treated robots as successors to the digitally servoed numerically controlled machine tools of the 1950s, and he borrowed from the cam mechanisms used in high-speed dedicated assembly machines. A cam cannot be used in a robot because its stroke and timing are fixed, but the smooth "motion curves" developed for cams can be reproduced in software, an approach known as electric cam or smart cam control.[1] The robot's motions were programmed on NEC's TK-80 8-bit microcomputer kit, and the group developed a new motion curve, "NC2", in which the deceleration interval is twice the acceleration interval, which prevented vibration.[1] Makino and N. Furuya presented the concept in a paper titled "Selective compliance assembly robot arm" at the first International Conference on Assembly Automation in Brighton in March 1980.[1]

Makino also patented a variant of the arm. United States Patent 4,341,502, "Assembly robot", filed in March 1980 and granted on 27 July 1982, describes an arm built as a quadrilateral (four-bar) linkage, with the drive devices for two adjacent links mounted on the base and the assembly tool at the joint of the other two links.[3] The patent says that in the earlier serial arm, where the second link's drive rides on the first link, that drive becomes a load on the first link's drive; moving the drives to the base keeps the arm light.[3]

### Commercialization

After the three years of joint research, some members of the group began developing their own SCARA robots, among them Sankyo Seiki Seisakusho, whose commercial model was named SKILAM.[1] At the International Robot Show held at the Harumi Exhibition Center in Japan in autumn 1981, five manufacturers demonstrated SCARA robots.[1] Makino identifies the first industrial use as an audio-board assembly line at Pioneer's Oomori plant, which used eight Sankyo SKILAMs.[1] In 1982 IBM announced that it would sell the Sankyo Skilam under its own name as the IBM 7535, obtained on an OEM basis; Yamafuji calls this the first international recognition of the SCARA.[13]

Seiko Epson's robot business grew out of watchmaking. In 1981, a team of seven at the company began building a flexible production system for assembling small watch parts, and Epson produced its first SCARA robots in May 1983. Its first commercial line, the SSR-H series, had a position repeatability of plus or minus 0.015 mm and a maximum operating speed of 2 meters per second, according to the company.[5]

Makino's 2014 review gives the wider context. At the end of 1981 there were fewer than 40,000 industrial robots in the world, and by 1992 there were 560,000; about 60% of them were in Japan. He estimates, while noting that the figure is not certain, that about 25% of Japanese robots in those years were SCARA robots.[1]

### Timeline

| Date | Event |
| --- | --- |
| April 1978 | SCARA research group begins work with Makino (five companies in his account, thirteen in Yamafuji's)[1][13] |
| July or October 1978 | SCARA Prototype I built (Yamafuji gives July, Makino October)[1][13] |
| March 1980 | Makino and Furuya present "Selective compliance assembly robot arm" at the 1st ICAA, Brighton[1] |
| May 1980 | Prototype II built, with tacho-generator feedback[1] |
| Autumn 1981 | Five manufacturers demonstrate SCARA robots at the International Robot Show, Harumi[1] |
| 1981 | SCARA robots introduced to commercial assembly lines[2] |
| 1982 | IBM announces the IBM 7535, an OEM version of the Sankyo Skilam[13] |
| 27 July 1982 | US Patent 4,341,502 granted to Makino[3] |
| May 1983 | Epson produces its first SCARA robots; its SSR-H series is released that year[5] |
| 2006 | SCARA inducted into the Robot Hall of Fame[1][2] |

### Robot Hall of Fame

The Robot Hall of Fame was set up in 2003 by the School of Computer Science at Carnegie Mellon University. In 2006 the SCARA was inducted alongside AIBO, David, Gort and Maria. It was the second industrial robot inducted, after Unimate, and the third Japanese robot, after [ASIMO](https://aiwiki.ai/wiki/asimo) and Astro Boy; Makino attended the ceremony as its developer.[1] The hall's citation credits the arm with high-speed automated assembly and the mass production of small electronic products.[2] The citation quotes Matthew T. Mason, whom it identifies as director of Carnegie Mellon's Robotics Institute: "SCARA mirrors the 'design for assembly' movement in automated manufacturing, capitalizing on the additional simplicity that is possible for properly engineered products, and enabling the inexpensive modern electronic products that we now take for granted."[2]

## Design

### Joint layout

In Makino's Prototype II, the first axis, nearest the base, is a rotary joint about the vertical axis driven by a DC [servo motor](https://aiwiki.ai/wiki/servo_motor) with an optical encoder, a tacho-generator and a [harmonic drive](https://aiwiki.ai/wiki/harmonic_drive) reducer. It swings a plate-like first arm, at the end of which sits a second rotary joint of much the same construction, also turning about a vertical axis. The tool axis at the end of the second arm moves straight up and down: early versions used a pneumatic cylinder for this thrust, later replaced by a ball screw. The fourth axis rotates the tool, driven by a stepping motor mounted under the first axis through a one-to-one timing belt, so the tool keeps its orientation while the arms move unless the stepping motor is commanded to turn.[1]

Makino summarized the arrangement as planar positioning, including orientation in the plane, plus a single straight tool motion, and wrote that almost 80% of assembly tasks are said to be done by this kind of one-direction movement.[1] The robotics textbook *Modern Robotics* by Kevin Lynch and Frank Park models the SCARA as an RRRP open chain (three revolute joints and one prismatic joint) widely used for tabletop pick-and-place. Its end-effector pose is fully described by four numbers $(x, y, z, \phi)$, the Cartesian position of the tool point and the tool's angle in the horizontal plane, so the task space is usually taken as $\mathbb{R}^3 \times S^1$, and every orientation $\phi$ can be reached at every reachable point.[4]

### Kinematics

Since the arm sets the tool's horizontal position with its two rotary joints and moves the tool vertically with a separate straight axis,[1] the horizontal position depends only on a planar two-link (2R) chain of the kind analyzed in robotics textbooks. For link lengths $L_1$ and $L_2$ and joint angles $\theta_1$ and $\theta_2$, the tool position in the plane is:[4]

$$x = L_1 \cos\theta_1 + L_2 \cos(\theta_1 + \theta_2), \qquad y = L_1 \sin\theta_1 + L_2 \sin(\theta_1 + \theta_2)$$

With $L_1 > L_2$, the reachable region (ignoring joint limits) is a ring with inner radius $L_1 - L_2$ and outer radius $L_1 + L_2$. A point outside the ring has no solution, a point on its boundary has one, and a point inside it has two, the "lefty" and "righty" (or elbow-up and elbow-down) configurations.[4] Finding the joint angles for a given tool position is the inverse kinematics problem. For the two-link chain it has a closed-form solution from the law of cosines: with $\gamma = \operatorname{atan2}(y, x)$,

$$\beta = \cos^{-1}\!\left(\frac{L_1^2 + L_2^2 - x^2 - y^2}{2 L_1 L_2}\right), \qquad \alpha = \cos^{-1}\!\left(\frac{x^2 + y^2 + L_1^2 - L_2^2}{2 L_1 \sqrt{x^2 + y^2}}\right)$$

the righty solution is $\theta_1 = \gamma - \alpha$, $\theta_2 = \pi - \beta$, and the lefty solution is $\theta_1 = \gamma + \alpha$, $\theta_2 = \beta - \pi$.[4]

## Applications

The Robot Hall of Fame names pick-and-place, assembly and packaging as the tasks the design excels at.[2] FANUC lists assembly, pick-and-place, inspection and packaging for its SR series, offers food and cleanroom variants with food-grade grease and ISO Class 5 cleanroom compliance, and markets a rack-mounted model for fast transport of small parts such as solar cell modules.[7] Early uses include Pioneer's audio-board line, Sankyo's own assembly of floppy-disk magnetic heads, small motors and music boxes from 1981, and Epson's watch assembly.[1][13][5]

FANUC also sells a ceiling-mounted model, the SR-3iA/U, which it says removes the "dead zone" that it describes as common on traditional SCARA robots.[7]

## Manufacturers and products

The table lists examples from manufacturers' own material; figures are company specifications.

| Manufacturer | Line | Details |
| --- | --- | --- |
| Sankyo Seiki Seisakusho | SKILAM | Early commercial SCARA; eight used at Pioneer's Oomori plant[1] |
| Epson | SSR-H (1983) | Epson's first commercial SCARA line; repeatability plus or minus 0.015 mm, 2 m/s[5] |
| Epson | GX, LS, LA, RS, T series | Reach 175-1,000 mm, payloads up to 50 kg, "more than 300 models"[6] |
| [FANUC](https://aiwiki.ai/wiki/fanuc) | SR series (SR-3iA to SR-20iA) | Four-axis; payloads 3-20 kg, reach up to 1,100 mm[7] |
| Yamaha Motor | YE4, YE10 (2026) | Payloads 4 kg and 10 kg; aimed at China, ASEAN countries, India and Japan[8] |

Epson describes itself as the world's number one SCARA maker; its product page gives no data source or year for that claim.[6] An Epson Robots announcement in April 2026 said Epson Robots had sold over 250,000 robots worldwide, a figure that covers its SCARA and six-axis robots together, based on its internal sales data through April 2026.[9]

### Developments in 2026

Several manufacturers renewed their SCARA lines in 2026:

| Date | Manufacturer | Announcement |
| --- | --- | --- |
| April 2026 | Epson | LS50C, the largest-payload SCARA in Epson's range, with 50 kg payload and 1,000 mm reach[9] |
| June 2026 | Epson | LS-C series (LS4-C, LS8-C, LS20-C) for Europe, available from May 2026 and replacing LS-B models, with the RC800-A controller and optional force sensing and conveyor tracking[10] |
| July 2026 | Yamaha Motor | YE4 and YE10 SCARA robots and RCX440 controller; the absolute battery that keeps home-position data draws less power and sits on the robot, so the home position need not be recalibrated after installation or relocation[8] |

## Research and learning-based control

SCARA arms also appear in research on [robot learning](https://aiwiki.ai/wiki/robot_learning). In a 2024 study, Jonathan Salzer and Arnoud Visser tested whether the [RT-1-X](https://aiwiki.ai/wiki/open_x_embodiment) robotic [foundation model](https://aiwiki.ai/wiki/foundation_models) could control a robot type it had not seen in training: a UMI-RTX SCARA arm. The model did not work zero-shot on the SCARA, but after [fine-tuning](https://aiwiki.ai/wiki/fine_tuning) on demonstrations the robot learned a pickup task. With an object that appeared in the foundation model's data but not in the fine-tuning set, only the skill transferred, not the object-specific knowledge.[11]

A 2024 paper by Michael Meindl, Raphael Mönkemöller and Thomas Seel extended a learning-control method called Autonomous Iterative Motion Learning (AI-MOLE) to multi-input, multi-output systems and tested it in simulation on a simplified SCARA robot meant for automated injection of stem cells into heart muscle. In that simulation the method reached highly precise reference tracking in as few as 15 trials per motion without a model of the robot or manual parameter tuning; the authors note that real-world results are still needed.[12]

## See also

- [Industrial robot](https://aiwiki.ai/wiki/industrial_robot)
- [Collaborative robot](https://aiwiki.ai/wiki/collaborative_robot)
- [End effector](https://aiwiki.ai/wiki/end_effector)
- [Automation](https://aiwiki.ai/wiki/automation)
- [AI in manufacturing](https://aiwiki.ai/wiki/ai_in_manufacturing)

## References

1. Makino, Hiroshi. "Development of the SCARA". Journal of Robotics and Mechatronics, Vol. 26, No. 1, pp. 5-8, February 20, 2014. https://doi.org/10.20965/jrm.2014.p0005
2. The Robot Hall of Fame (Carnegie Mellon University). "SCARA" (2006 inductees). Archived copy of robothalloffame.org. https://web.archive.org/web/2016/http://www.robothalloffame.org/inductees/06inductees/scara.html
3. Makino, Hiroshi. "Assembly robot". US Patent 4,341,502, filed March 24, 1980, granted July 27, 1982. https://patents.google.com/patent/US4341502A/en
4. Lynch, Kevin M.; Park, Frank C. "Modern Robotics: Mechanics, Planning, and Control". Cambridge University Press, 2017 (preprint dated May 3, 2017), Example 2.9 and the introduction to Chapter 6 (Eq. 6.1, Figure 6.1). https://hades.mech.northwestern.edu/images/7/7f/MR.pdf
5. Epson. "Four Decades and Looking Forward: Catching Up with Epson Robots Chief Keijiro Naito". Epson Insights, February 22, 2025. https://blog.epson.com/catching-up-with-epson-robots-chief-keijiro-naito/
6. Epson. "SCARA Robots". Epson America, accessed November 18, 2026. https://epson.com/scara-robots
7. FANUC Europe. "FANUC SCARA Robots". FANUC, accessed November 18, 2026. https://www.fanuc.eu/eu-en/scara-series
8. Yamaha Motor Co., Ltd. "Yamaha Motor Launches New YE4 and YE10 SCARA Robots and RCX440 Controller". July 23, 2026. https://global.yamaha-motor.com/news/2026/0723/scara.html
9. Epson Robots. "Epson Robots Expands SCARA Lineup with High-Payload LS50C". Robotics Tomorrow, April 29, 2026. https://www.roboticstomorrow.com/news/2026/04/29/epson-robots-expands-scara-lineup-with-high-payload-ls50c/26499/
10. Epson Europe. "Epson unveils LS-C series SCARA robots with faster cycle times and advanced safety". Epson Press, June 2, 2026. https://press.epson.eu/en_GB/news/epson-unveils-ls-c-series-scara-robots-with-faster-cycle-times-and-advanced-safety/
11. Salzer, Jonathan; Visser, Arnoud. "Bringing the RT-1-X Foundation Model to a SCARA robot". arXiv:2409.03299, September 2024. https://arxiv.org/abs/2409.03299
12. Meindl, Michael; Mönkemöller, Raphael; Seel, Thomas. "Autonomous Iterative Motion Learning (AI-MOLE) of a SCARA Robot for Automated Myocardial Injection". arXiv:2409.06361, September 2024. https://arxiv.org/abs/2409.06361
13. Yamafuji, Kazuo. "Development of SCARA Robots". Journal of Robotics and Mechatronics, Vol. 31, No. 1, pp. 10-15, 2019. https://doi.org/10.20965/jrm.2019.p0010

